MCC update-> Lost config files (CaZaE)
Some Info:MCC : 3.66MPLAB : 5.1 After pass in MPLAB 5.1 I update the MCC. After that all my project load empty MCC config. I have a MyConfig.mc3 and a device_config.mcc files. In the second one all my...
View ArticleMCC dsPIC33CH128MP502 (DDuck007)
Hello,I have a problem using the MCC with above mentioned controller.I use MPLABX 5.10 an Windows 10.The problem is, that the actual version of MCC has PWM implemented, so if I start a new project the...
View ArticleMissing I2C pad control registers on 18FxK42 (thistle)
According to the datasheet (table 16-10), the following pads are special I2C pads with additional registers:RB1RB2RC3RC4RD0RD1 In MCC, you can only set register RB1I2C (when using I2C1) or RB2I2C (when...
View ArticleMCC does not generate code for INLVLx (jswanson)
PIC18F26K83MCC 3.66, Core 4.56, Lib 1.75 There are entries in the Register tab for the INLVLx registers, but MCC doesn't generate any code. Jeremy...
View ArticleMCC creates a bad "#if (__XC8_VERSION
Hi Folks, It looks like the MCC will create a bad section in the PIN_MANAGER.C file. It creates: #if (__XC8_VERSION <= 1410) typedef union { struct { unsigned T2INPPS :6; }; struct { unsigned...
View ArticleCAN SPI Slave Select using MCC (MarcelC)
Hello, I have the following problem: When I integrate the CAN SPI Libary, the SPI interface MSSP1 is integrated at the same time. Then comes the Message "Selesct a SPI Slave Select Pin" But there is no...
View ArticleUSB Device not recognized at Computer startup (scroteau)
Accidentally posted this in Harmony forum Device is recognized if plugged in after computer has bootedDevice not recognized if plugged in before computer powered on, even after unplugging and plugging...
View ArticleMCC v3 generated circular buffer questions in interrupt handlers. (mpittman)
I am using MCC v3 and MPLABX v5.00 to generate code for a PIC24F. When I review the code generated for the uart rx and tx interrupt handlers it appears to be using the circular buffer incorrectly (or...
View Articlepic24fj256gb106 MCC OC1Interrupt (dosio)
Hello, I have problem with generating Interrupt with OC1 (the same is and with OC2). Processor is pic24fj256gb106. MCC genarate : void OC1_Initialize (void) { // ENFLT0 disabled; OCSIDL disabled; OCM...
View ArticleMPLABX 5.10 with MCC v3.66 ECAN Error (WorkingHard)
Hi, Reposting this from MPLAB forum. I am playing around with MCC V3.66 to set up ECAN on the dsPIC33EV 5V CAN-LIN board. I recently updated my MCC and MPLABX versions from MPLABX V5.05 and not sure...
View ArticleUART1, PIC32MX230F256B and compiler errors (Aethelstan)
Hi, I am playing with the MCC 3.66 on a PIC32MX230F256B and I am trying to get the UART streaming data. I am not trying to do anything fancy just yet, simply use some of the examples. Using the code as...
View ArticleLIN 2.0 diagonstic frame (Jianxin.Pang)
Is it possible for MCC LIN driver 2.3 to use both signal frame and diagonstic frame ?Because for signal frame, Lin2.0 uses enhanceed pararity ,but for diagnostic frame it uses classic pararity . so i...
View Articlefoundation service I2C code example (soleil_sword)
Hi, I'm trying to use foundation service I2C driver library.The code looks quite clean, however I couldn't find any sort of examples on how to use the library, is there documentation or code example to...
View ArticleMCC-LIN newbie for PIC16F1825 (LunguFlorin)
Hi,A couple of days ago I discovered the MCC, i'm working on a project where I need to implement a LIN bus system (3 PIC16F1825 - 1 Master, 2 Slaves), I configure the MCC for my setup and I generate...
View ArticleMCC not able to load configuration anymore (Qwerty8787)
Hello, few hours ago I made a copy of my PIC18F65K40 project to verify memory usage using PIC18F66K40. After opening the second project, MCC asks me if I want to import the configuration and that the...
View ArticlePIC16 MPLAB X MCC LIN Stack Read back transmitted data (RonGer)
Dear all, the MCC LIN_Stack offers no capability to read back the data that have been transmitted on the bus.Unfortunately the reception functionality gets disabled in the LIN_handler() subroutine.Does...
View ArticleSuggestions for the next release of MPLAB® Code Configurator (florin.matei)
This thread is dedicated to gathering suggestions related to what features could be improved or added in the next release of MCC. Please try to provide some arguments for your suggestions as they will...
View ArticleInstall device library for MCC? (twelve12pm)
I downloaded MPLAB Code Configurator v3.16 and installed it into MPLAB X IDE v3.40. Out-of-the-box, it does not support dsPIC33FJ128MC804. So I downloaded PIC24/dsPIC33/PIC32MM Device Library,...
View ArticleIssue with MCC generated bootloader (beard007)
Hi, I'm using pic18f27J53 with MCC generated bootloader.The UnifiedHost 0.1.14 consistently failed to see the bootloader with the message (console output) "Device Failed to respond to command...">...
View ArticleMCC is unsupported PIC18F47K422 (NirVM)
Guys, Trying to create a Bootloader for my project, I run the MCC and follow the Bootloader Generator User Guide but when trying to fetch the Booloader Generator resource from the device resource list...
View Article