SPI Clock Frequency Warning (cinpezzo)
Hi,I'm configuring the SPI Clock frequency of PIC24EP512GP204 using MCC v3.25 in MPLAB v3.45 but, if the clock goes over a certain frequency (in my case over 10MHz) the MCC shows the attached warning.I...
View ArticlePIC 8 Bit - IOC Issues (Allexubes25)
I know im not on the right forum page,but i cant seem to open a new page with my question.I have a problem with setting up the MCC on MPLABX 3.55 C8. is giving me the following error message,and i know...
View ArticleExtended Sampling Time (PIC_Fan2016)
Hi guys,does any one know how long is the Extended Sampling Time of ADC converter? Im using PIC18F97J94. Thank!..
View ArticleInterfacing PIC18F4550 and MFRC522 (shreyaravi)
Hello! I am trying to read the version register from the MFRC522 using SPI in PIC18F4550 to check if there is a connection established between them. But when I display the read value in a LCD the value...
View ArticleMigrating from old MCC to MCC v3 (craigjbradley)
I have some older projects using the original MCC. MCC v3 doesn't seem to recognize the configuration files. Does any know how to get MCC v3 to load the old files? Tnx,Craig..
View ArticleEUSART Use With Interrupts (Ted M)
I'm using MCC-generated code for EUSART on a PIC18F27K40 and I've checked the box to enable EUSART Interrupts. What I'm looking for is simple guidance on how to send and receive bytes over the USART....
View ArticleI2c Code stuck with status==I2C2_MESSAGE_PENDING (CScotty)
I'd like to use the Code Configurator's generated code for I2C, whilst it's more than I need there seems to be no good justification for re-inventing the wheel. My code is based very closely on the...
View ArticlePIC18F26K22: MCC how to disable ECCP1 PIN in TMR1/compare mode ? (j2423)
Using the MCC, unable to disable the ECCP1 pin. Datasheet PIC18F26K22 says: 14.2.3 SOFTWARE INTERRUPT MODEWhen Generate Software Interrupt mode is chosen (CCPxM<3:0> = 1010), the CCPx module does...
View Article"Click into MCC" problem (Dr_Sian)
I'm trying to get up and running with adding Click boards to projects using MCC.Having failed with the Weather click, I tried to replicate the DiffPressure click video on YouTube - the "how to" #1...
View ArticleLIN LIBRARY SUPPORT USING MPLAB CODE CONFIGURATOR (sutarabhijit1)
hey i am using lin library of mplab code configurator . i use 18f24k22 pic with pickt3 debugger. i made communication between master and slave but i did not get any response from slave when i debug Lin...
View Articledid not get data from LIN SLAVE TO LIN MASTER (sutarabhijit1)
hey i am using two 18f24k22 pic mc with mcp2021500 lin trans-receiver ic. one board is master and another is slave.for this i used mplabx ide v3.55 with mplab code configurator v3.26.2. from mcc i got...
View ArticlePIC18F97J94 Support (AE Engineering)
Support for this part is long over due. Any beta versions available? Request was made a couple years back for this part to be supported by others...
View ArticleEUSART read and write using MCC 3.26.2 and PIC16F1778 (PStechPaul)
I am trying to use the EUSART of the PIC16F1778 with interrupts to avoid time delays for transmitting strings, and polling for receiving characters. Here is the code generated by MCC:(In...
View ArticleMCC I2C (sascha_focus)
Hello,I have some problems / questions about the I2C code of the MCC. To read / write a byte I use the following code: //#define buffersize 20static unsigned char writeBuffer; //Buffer for I2C...
View ArticleI2C with Microchip Code Configurator - RTCC (Dirkiek)
Hi Guys, I'm learning to use the I2C communications of my PIC18F46K22. I would like to read and write to a RTCC. Is there a tutorial or link that I can work trough that can assist me in learning how to...
View ArticlePWM Bug in MCC V3.26.2 with dsPIC33EP128MC506 (JT)
Hi, I lost 2 days on trying to use PWM2 output... the initialization code generated in pwm.c PWM_Initialize() is wrong for registers IOCON2 and FCLCON2.And it will be better to enable the PWM...
View ArticleMCC UART module (Severino)
I'm trying to configure a dsPIC33EV256GM102 using MCC v3.26.1 (in MPLABX v3.60). In the UART module I'd like to set register U1MODE to TX_RX_RTS, but the only available option is TX_RX.I know I can...
View ArticleIssues using Unified Bootloader Host with MCC generated bootloader (FabianL)
Hello, I'm using pic16f18326 with mcc generated bootloader (new reset vector at 0x300 - all working well) and I'm somewhat struggling with the existing Unified Bootloader Host Application (0.1.3). At...
View ArticleGetting error message trying to use MCC with PIC24HJ32GP202 (electronicsArtist)
Hello I am beginer embedded programmer I am trying to use the Code Configurator plug in on mplab but i get an error messgae saying MCC doesnt support device I am wondering does is MCC only for certain...
View ArticlePIC32MM and ADC using MCC (Claudio one)
Hi guysI'm starting to use the 32MM series , very nice MCU , i understand almost all and it's working but i have just a problem with ADC and i suspect in a bug or my fault but i don't understand the...
View Article
