Opening MCC 2.25 configuration files with 3.0 (cintet)
Hi, It is possible to open/import 2.25 MCC generated files with 3.0?? Regards...
View ArticleMCC v3 EUSART pin direction bug (NicholasLee)
With MCC v3, if you choose a PIC16F1824 and they then add a EUSART component, when you tick the box to āEnable Transmitā, it adds the TX pin, but with both the RX and the TX pins set as inputs. Thatās...
View ArticleFLASH READ/WRITE Functions Use Too Much RAM (JohnWill)
An issue I ran into using the 12F1501 is that I wanted to store a config word into FLASH, so I tried using the MCC generated FLASH read/write functions. They seem to be hard wired to read/write 16...
View Articlepwm module adjutment (hasanyildiz)
Hi,I am using PIC24FJ128GB204 and Code configurer to setup hardware but in code configurer there is not pwm hardware. Do anyone know Is it not supported or what can be the problem?Thank you in advance...
View ArticleNO SPI CLKIN PINS IN SLAVE MODE (davea)
need some help with MCC 3.0.4clkin pins not showing upis the only work around to set it up as master and set it's pins to inputs then in the main set it to slavealso can you chain 3 pins together (1...
View ArticlePIC16F1829 MCC problem? (Skoul)
Hi,I am trying to create a project based on 16F1829 using MPLAB X 3.30 (clean installation), XC8 1.37 and Mcc 3.05.So far I have noticed 2 errors. 1. Building the project from scratch, I can add both...
View ArticleMCC loses / changes Custom Names on GPIO (I/O Pins) (pchidley)
Using MCC 3.05 with MPLAB X 3.20, product using PIC24FJ1024GB610 I wanted the RTCC output to come out on a pin so I set the defaul RTCCOUT pin to a GPIO Output. My bad. You need to set it in the RTCC...
View ArticleMCC v3.0.5.1 : issue with PIC16F1619 (Curiosity board) (RISC)
Hi, I use MPLAB X v3.26, XC8 v1.37 and MCC plugin v3.0.5.1 on Curiosity board.I chose a system frequency from 250kHz and generate a project which is just mixing 2 PWM frequencies.After generating the...
View ArticleHow to Enable WPU, IOCP or IOCN (dcarrington)
First time user of MCC 3.03.Environment:MPLAB X 3.20XC16 1.25PIC24FV32KA301Using the MCC Pin Module I have successfully set PIC24 pins to their appropriate mode. In my case, there is one A/D channel, 5...
View ArticleSupported Devices List (CScotty)
Where can i find a list of devices supported by each version of the Code Configurator? Thanks...
View ArticleMPLAB Code Configurator does not apply changes (aeromorph)
Hello, I have this following recurring error on when using Mplab code configurator 3.0.5. I create the configuration the first time, and it seem ok. If I go to MCC again and make changes, when I click...
View ArticleHow do I initialize a function? How do I call the function from code...
I have question on how to initialize a function from Code Configurator also how do I call the function from Code Configurator?I believe I have the Code Configuration options set up correctly. Just need...
View ArticleErratic behavious of ICD3 (Hari21)
Hi, I have been working with ICD3 for programing microcontrollers for over a year now. A problem that I have always faced is the erratic behavious of ICD3. While programming, my ICD3 will usually give...
View ArticleMCC and bootloader code, part of code refers to another pic (carloca)
Hi,just playing with the newly installed MCC, and my goal is to have a bootloader done for a pic18f25k22I added resources Bootloader generator and Eusart to the MCC, I have NO error during code...
View ArticleCode Configurator Pin Manager for Alternate packages (petEEy)
Is there a way to change the graphical representation of the target device to different pin configurations that vary with packages? The graphical representation of the chip would be intuitive and...
View ArticlePIC24FJ256GB406 DAC configuration bug (maarten a)
Hi,I found a small bug in mplab mcc v3.0.5 that results in continues crashing of the chip. If you enable the DAC, TRISG will be set to 0x1CC, this is incorrect. The datasheet specifies: When using the...
View ArticleMCC I2C - Repeated start (ultiblade)
Hi all, I'm trying to interface a MMA8452 acceleration sensor over I2C using a 18F44K22 and the code generated by MCC v2.25.2 for an I2C master. So far this is not working. It only returns 0x00's on...
View ArticleList of PIC MCUs supported by Code Configurator (lightaiyee)
I intend to use PIC18LF25K50. Does Code configurator support this MCU? Where can one get a list of PIC MCUs that are supported by Code Configurator?..
View ArticleCAN support (jswanson)
Are there any plans to support PIC18F45K80 or any other devices with a CAN module?..
View Articledo you have any plan to support dsPIC in MCC? (grchy)
Hi, I am a big fan of PIC MCU. And most of MCU I used on work is dsPIC series. So do you guys have any plan to support DSC in MCC, if you do, when is it going to release? Thank you !..
View Article