Quantcast
Channel: MPLABĀ® Code Configurator
Browsing all 2062 articles
Browse latest View live
↧

UART loop back program (dsPIC33EV32GM104) not working (vijayakumar.sargunam)

Hi, I am trying to do UART loop back program using dsPIC33EV32GM104. program environment is created using MCC plugin. I getting expected output sometimes. I successfully transmit the character from...

View Article


MCC with PIC32MZ2048EFH064 not working (chempner)

I'm working on a project and when i wanted to open the MCC in MPLAB X v5.45 the following message popped up: (attachment) I already installed the PIC32MZ MCC Library from the official Microchip...

View Article


MCC with PIC32MZ2048EFH064 not working (chempner)

I'm working on a project and when i wanted to open the MCC in MPLAB X v5.45 the following message popped up: (attachment) I already installed the PIC32MZ MCC Library from the official Microchip...

View Article

LIN_Slave_Only_Response_To_PID_0x00 (Interrupt)

I'm trying to create a LIN network using PIC18F26Q10 as master and PIC16F18446 as slave using "MCC LIN stacks"I can't seem to get the Slave to respond to any other PID then 0x00. I've tried to...

View Article

PIC 18F4423 (K3PTO)

I have a need to program the 18F4423 in a legacy product. I would like to use MCC and the XC8 compiler. However,when I try to start MCC I get the following warning: project's device is not supported by...

View Article


MPlabX IDE 5.45 want to learn coding (Madhusudan)

HI , I am three years experience in embedded field but i am new to this pic.I am using PIC24FJ128GC006 for one of my project I am feeling some difficult in coding part . can any one help me in MPLABX...

View Article

Coding help (Madhusudan)

Hi, Whether microchip will give me coding service . I want to write code for one of my project .whether is there any service available with microchip..

View Article

Selecting more than 4 ADC channels using MCC plugin for dsPIC33EV32GM104...

My project needs 7 analog input channels for interface with different sensors. I created a MCC based demo project for testing the ADC module of dsPIC33EV32GM104. while configure for multichannel ADC...

View Article


PIC12F675 shows library errors on MCC tool under MPLAB-X IDE (sunils)

I have installed MPLAB X , then XC 8 compiler. Now in MPLAB X under plugins, I have installed MCC. Now created new project for PIC12F675. Clicked on MCC option but one issue has populated. It shows...

View Article


MCC support of CAN FIFO mode in PIC18F (leosw)

Hello world, It's a revolution, I'm discovering MCC and I'm trying to use it in a new design. I'm working with a PIC18F45K80 (with ECAN module) and I'm trying to setup it in MCC. It seems that the FIFO...

View Article

Timeout Driver: how to use the timeout_callNextCallback() function outside...

I want to use the Foundation Service's Timeout Driver in my application that runs on a PIC24FJ128GA106. In the MCC v4 I added the driver linked to TRM1. My application is developed as a state machine...

View Article

trying to get SAME51 Curiosity Nano board working (davea)

Hi, everyoneI just received EV76S68AMPLAB X IDE v5.35MCC v4.02downloaded XC32 v2.50started a new projecteverything look good untill I click MCCit opens up empty and gives a warning boxI go there and...

View Article

Issue in getting signal from CAN TX pin of dsPIC33EV32GM104...

Hi, I am testing CAN program generating through MCC plugin for dsPIC33EV32GM104. I try to transmit a CAN message with ID 0x220 continuously and testing it using CAN bus analyzer. I assigned pin no 43...

View Article


Renaming master.X & slave.X files (GettinBetter)

REF: dsPIC33CH128MP508 Hi Peeps, As I remember, there was an issue with renameing the master.X and slave.X is this still the case? I'm halfway through starting a new project and realised that I've...

View Article

Buggy MCC behavior with PIC18F45Q10 (kaamil1984)

Hi guys, I have found 2 serious bugs in code generator, when PIC18F45Q10 is selected. 1. I'm using MSSP1 in SPI mode. I have set MSSP SDO1 to PC4, SDI1 to PC5 and SCK1 to PC6. (holy crap its 2021 and I...

View Article


MCC doesn't show Watch Dog timer period (VatchCat)

Hi everyone. I was trying to set up my WDT, but MCC doesn't show its period. What is possibly wrong with it? Thanks a lot for any tip.Use: Windows 10MPLab IDE 5.40 VMCC 4.02PIC 18F27K40..

View Article

How Can I print mcc's pin table (davepl)

I'm starting a pcb for my PIC32MX application and I wish to customise the electronic schematic part's pin names. Not being able to find a control to do this in mcc-4.0.2 I googled and was presented...

View Article


MCC selects wrong 48 pin TQFP for dsPIC33EV256GM004 (bricey)

Hello Folks, Hopefully someone can point me to a solution on this. I suspect that the chip is not supported but here it goes anyway. I have purchased the chip in the title which is a 44 pin 10x10x1...

View Article

PIC18F26K42 I2C slave mode options seem misleading (oliverb)

So the address byte is described as having a range of 0-7F (7 bit address), but the value you give is the value actually written to the address register and going by the datasheet that is in 8 bit form...

View Article

I think the clock setting of PIC18F47J13 by MCC is wrong (mmatsui)

The code generated by MCC is as follows.void OSCILLATOR_Initialize(void) { // SCS FOSC; IRCF 4MHz; IDLEN disabled; OSCCON = 0x60; // INTSRC 31KHz; PLLEN disabled; TUN0 0; OSCTUNE = 0x00; // ROSEL...

View Article
Browsing all 2062 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>