Is The Code Generateor Has Many Bugs? (garypty)
I did not programming with Microhip MCU for a long time. Recently as my customer require, I start to use the PIC32MM MCU again. I find that Microchip provide a Code Generator with the new MPLAB X IDE,...
View ArticleTCPIPLite Stack sends corrupt packets (alecdavis)
Microchip Code Configurator version 3.25PIC18F67J60when the ETH_EventHandler is called from the Network.c:Network_Manage() from main loop, some times ethData.bufferBusy hasn't been cleared, thus...
View ArticleTimer2/4/6/8 Interrupt (PIC_Fan2016)
Hi guys,im using PIC18F97J94 and wanna use timer 8 increment from 00h until they match PR8. If TMR8 = PR8, the interrupt should be occur. Every thing works so far ok, but the is a problem I couldn't...
View ArticleBug on Memory driver MCC 3.25 with 18F47K40 (SebKister)
Mcc generates DATAEE_ReadByte and DATAEE_WriteByte with a uint8_t address parameter.18F47K40 EEProm is 0x3FF in size...
View ArticleBug on WPUx registers values with MCC 3.25 for 18F47K40 (SebKister)
All WPU off generates WPUx registers */ WPUD = 0x10; WPUE = 0x08; WPUB = 0x40; WPUA = 0x80; WPUC = 0x00;..
View ArticleMCC button icon and what it not doing (swmcl)
Hi,I'm new to this software (v3.45).I have been trying to configure my first project and now I start again with the same chip on a second basic project. When I have built my new project and I have set...
View ArticleMCC v3.25 still generates wrong OSC with PLL setup... (cteufert)
The long awaited correction to MCC to address the OSC with PLL configuration affecting timers, UART, etc. has yet another problem in the recent release. The problem is when selecting the PLL divisor...
View Articlemigrate from Code configurator V2.25.2 to V3xx (wendysh)
have a number of projects written using code configurator V2.25 and MPLABX V3.05, i have now updated my computer and have MPLABX 3.45 and code configurator V3.25 but cannot open earlier code...
View Articleno value set for setting "flag" in register "IOCI" (jastmc)
I using a PIC24FJ1026GA606, MPLABX3.45 & MCC 2.35. In the MCC notifications/Pin module, I get a warning:no value set for setting "flag" in register "IOCI" The Generate button results in a failure...
View Article24EP512GP204 OC1 PWM frequency (cinpezzo)
Hi all,I need to generate a 13MHz clock output to run an external device so I'm trying to configure the OC1 with MCC.My configuration is:Fosc/2 = 52MHzand I configured OC1 in MCC as in the attached...
View ArticleMCC Bootloader Generator HIGH/LOW interrupt vectors are reversed (alecdavis)
Microchip Code Configurator: 3.25 (which includes TCPIPStackLite2.10)Device: PIC18F67J60 file pic18f_bootload.c// Memory Map // ----------------- // | 0x0000 | Reset vector // | | // | 0x0008 | High...
View ArticlePIC24FJ128GA202 SPI Baud Rate range (molrse)
Hi, according to the datasheet DS30010038B-page 236 the SPI Baud Rate is defined as Baud Rate = FPB /(2*(SPIxBRG + 1)) Under DS70005136A-page 16 (Serial Peripheral Interface (SPI) with Audio Codec...
View ArticlePIC24FJ128GA202 GPIO 12 [DIP28] (molrse)
Hi, thank you very much for the MCC, It helps me a lot! This is a little tricky situation that I found, It seems to ends in a wrong configuration, I suppose: Interaction between “Pin manager:...
View ArticlePIC12LF1840 Code configurator (ash1994)
Hey guys, I hope y'all doing fine. I just wanted to know if i could use MPLAB Code configurator for a simple USART program plus processing code(only 1 peripheral used -EUSART).I used the code...
View ArticleMCC v3.25 still generates wrong OSC with PLL setup... (cteufert)
The long awaited correction to MCC to address the OSC with PLL configuration affecting timers, UART, etc. has yet another problem in the recent release. The problem is when selecting the PLL divisor...
View Articlemigrate from Code configurator V2.25.2 to V3xx (wendysh)
have a number of projects written using code configurator V2.25 and MPLABX V3.05, i have now updated my computer and have MPLABX 3.45 and code configurator V3.25 but cannot open earlier code...
View Articleno value set for setting "flag" in register "IOCI" (jastmc)
I using a PIC24FJ1026GA606, MPLABX3.45 & MCC 2.35. In the MCC notifications/Pin module, I get a warning:no value set for setting "flag" in register "IOCI" The Generate button results in a failure...
View Article24EP512GP204 OC1 PWM frequency (cinpezzo)
Hi all,I need to generate a 13MHz clock output to run an external device so I'm trying to configure the OC1 with MCC.My configuration is:Fosc/2 = 52MHzand I configured OC1 in MCC as in the attached...
View ArticleI2C generated code, and the Vishay VEML6040 (sirhC_sirhC)
I used the MCC to make an I2C master project for the PIC16F1825. Something I have done before, and used successfully with other i2c parts, such as an ST accelerometer for instance. Anyway, when I tried...
View Article
